Navigation

Quick Drain System

‹Return to Previous Page
Description

Description

A Factory installed system that uses a 5 amp pump to drain the bath after use. The Quick Drain System will pump out the tub in less than 60 seconds. The pumps drain pipe is a 1/1/2 inch PVG pipe and must be hooked up to the homes drain system. The 5 amp drain pump requires its own 15 amp GFCI all plumbing + Electrical hook ups should meet national, state, and local codes.  A top side air button activates the pump, simply push the button to start drain cycle and push it again to turn the pump off when the water has drained from the tub.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Quick Drain System”

Shipping & Receiving

Shipping

At WaterTech Whirlpools we ship our quality tubs across the United States using only the top freight lines to ensure your whirlpool tub gets to you on time and in the same condition as when it left our factory floor. 

The following are normal shipping times; please call for current shipping rates (subject to change).  Please note that shipping is NOT included in the price of each tub.  Regular delivery time is 3 weeks from the date we receive your order.

Our Quick Ship option allows your tub to leave our factory floor within 5 business days from the date we receive your order.   Please call 1-800-289-8827 for our Quick Ship service.

 

 

Precautions & Installation Tips

  • Do not lift or carry the whirlpool tub by the supply or return pipes - they could break or spring leaks.
  • You must install a mortar bed beneath your tub to meet code and warranty requirements.
  • An access opening large enough to service your pump must be installed to meet code requirements.
  • Do not frame your whirlpool tub enclosure until you have your tub on the job site.
  • Carpenters, plumbers, and tile installers should verify all dimensions to ensure that the tub enclosure is properly sized for your whirlpool tub.
  • Detailed installation instructions are available on the installation page of this site.
  • Re-test your whirlpool tub for leaks or construction damage before you enclose your tub.

 

Receiving

Reliable trucking (freight) companies have been selected by WaterTech Whirlpools to deliver each new Whirlpool Bath. WaterTech Whirlpools packages each bath individually to ensure safe delivery to each customer. The freight carrier will notify customer and schedule a delivery time after the bath leaves our manufacturing facility. Call WaterTech Whirlpools if you have any questions (i.e. price, product, technical, shipping etc.) Phone 1-800-289-8827, Fax: 423-926-6438 email at info@watertechtn.com.

INSPECTION AND CLAIMS PROCEDURE: Follow the steps below to eliminate any questions about who is responsible for visible or concealed damage that may have occurred in shipping. Examine the shipping box for signs of damage or mishandling, i.e. staples pulled loose, flaps unglued, punches to the box, severe indentations, or crushed corners. If the box is damaged, the delivery person and receiving person / Consignee must note the damage to the box on delivery paperwork before opening the box. Open the box and inspect the tub for damage. If damage is found, call WaterTech Whirlpools at 1-800-289-8827 before accepting tub. Minor defects such as scuffs, scratches, etc… can be easily taken care of by one of our service people. All issues need to be resolved before signing delivery paperwork.

CONCEALED DAMAGE: WaterTech Whirlpools allows the consignee / owner no more than 48 hours from time of receipt to inspect and report any concealed damage (i.e. leaks, broken pipes, etc…) or shortages of merchandise ordered (i.e. heater, drain, jet trim, etc…). Report concealed damage and shortage to Americas Best Whirlpools 1-800-289-8827.

FAILURE OF THE CONSIGNEE TO INSPECT AND REPORT ANY CONCEALED DAMAGE WITHIN THE 48 HOUR PERIOD PLACES FULL RESPONSIBILITY FOR ANY CONCEALED DAMAGE ON THE CONSIGNEE.

PRE-TEST YOUR TUB: You must pretest your tub for leaks within 48 hours of receipt. WaterTech Whirlpools tubs go through rigorous testing for plumbing leaks and proper operation prior to shipping, but as a secondary precaution, the tub must be re-tested for leaks and proper operation within the allotted 48 hours and before installation. Test your tub in a location that will not be damaged by spilled water such as a basement, driveway, or a garage. Pre-testing your tub allows you to find any plumbing connections that might have worked loose during shipping.

HOW TO PRE-TEST YOUR TUB: Place your tub on a firm flat surface, make sure top of tub is level in all directions. Tape over the drain. Fill with water to 1 or 2 inches above the highest jet. Plug the motor into a GFCI protected outlet, and with the pump running, check all pipes and fittings for moisture. If no leaks are found, remove tape over drain and check for proper drainage. If all is correct, you may continue the Installation process.

IF ANY PROBLEMS ARE DISCOVERED DO NOT INSTALL THE TUB UNTIL YOU HAVE SPOKEN WITH A WATERTECH WHIRLPOOLS REPRESENTATIVE AT 1-800-289-8827

Related Products

Expedited Production

Available to those who want to guarantee that their order will ship within 5 days after order is placed. Holidays and Weekends excluded.
$148.00

Additional/Custom Jet Locations

While all of our tubs are engineered to provide maximum hydrotherapy, we realize certain individuals may want or need special jet locations to provide them with hydrotherapy to particular body areas such as knees, feet,...
$51.00

Custom Pump Location

Customers needing to change a standard pump location to meet their particular building project need only to call Watertech. We can place the pump where you want it. All building codes require access to the...
$103.00

Drain/Overflow Finishes

Chrome: $48
Nickel: $72
Polished Brass: $55
Oil-Rubbed Bronze: $79
Watertech offers a beautiful variety of drain/overflow finishes for your tub, available in chrome, nickel, polished brass and oil-rubbed bronze. Note: PVC drain is 1 1/2" and fits all tubs.

LED Underwater Mood Light

By simply pressing a button the bather may transition through 8 colors while the last selection will automatically transition through all 8 colors.
$219.00

Grab Handles

Pricing is per pair

White, biscuit, or bone. Grab handles are not factory installed but are easily installed on the jobsite by contractor or plumber. Length 9 inches
$98.00

Tile Flange

An aluminum extrusion that is installed on the job. Used when tub is also to serve as a shower, can’t be used on oval or irregular shaped tubs.
$82.00

Injector Finishes

Chrome: $274
Nickel: $343
Polished Brass: $321
Oil-Rubbed Bronze: $370
Watertech offers a beautiful variety of injector finishes for your tub, available in chrome, nickel, polished brass and oil-rubbed bronze. Note: White and bone jets are standard in all tubs with some other colors available. For Walk-in bath tubs the standard finish is chrome.
$274.00

In-Line Electric Bath Heater with Ozonater

The in-line bath heater and ozonater operate when the pump is in operation.  The heater maintains the water temperature in your whirlpool and the ozonater automatically an additional level of sanitation.
$342.00

Aromatherapy

Watertech's new aromatherapy whirlpool system uses the aromatics of plant extracts and essential oils used baths and massages.  This unique system that can be factory installed on any Watertech whirlpool, air or combination massage tub. Air flows from the aromatherapy dispenser into the bath water and surroundings. Sample beads included in your first order. Cap finishes:  Biscuit, Bone or Chrome: $75 Metal finishes: Brushed Nickel, Oil Rubbed Bronze, Chrome: $95
$75.00
Back to top
Follow by Email
Facebook
Facebook
Contact us

We would love to help you answer all your questions. Please fill out the form below and we will get back to you ASAP or call us at: 1 (800) 289-8827.

Questions, issues or concerns? I'd love to help you!

Click ENTER to chat