<
Navigation
Description

Description

Watertech’s new Vibro Sonic Foot Massage System was developed to provide a shiatsu massage for the feet in any whirlpool, air, walk-in tub, soaking bath or combination bath. The system includes 2 Vibro Sonic pads each with its own electro magnetic motor. The pads are 3” in diameter with a silicone massager that protrudes from the center of each pad. The silicone massager softly compresses against the foot when the pad is turned on to massage the bottom of the foot from toes to heel. The Vibro Sonic System when combined with hot water is helpful to those who experience high blood pressure, poor circulation and foot discomfort. The system also includes, a 120-volt control center that plugs into a standard GFCI receptacle and an electronic keypad that turns the system on/off, provides 3 levels of vibration speed and pulsating intensity. Installation of the entire system is included in price.

Reviews (0)

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Shipping & Receiving

Shipping

At WaterTech Whirlpools we ship our quality tubs across the United States using only the top freight lines to ensure your whirlpool tub gets to you on time and in the same condition as when it left our factory floor. 

The following are normal shipping times; please call for current shipping rates (subject to change).  Please note that shipping is NOT included in the price of each tub.  Regular delivery time is 3 weeks from the date we receive your order.

Our Quick Ship option allows your tub to leave our factory floor within 5 business days from the date we receive your order.   Please call 1-800-289-8827 for our Quick Ship service.

 

 

Precautions & Installation Tips

  • Do not lift or carry the whirlpool tub by the supply or return pipes - they could break or spring leaks.
  • You must install a mortar bed beneath your tub to meet code and warranty requirements.
  • An access opening large enough to service your pump must be installed to meet code requirements.
  • Do not frame your whirlpool tub enclosure until you have your tub on the job site.
  • Carpenters, plumbers, and tile installers should verify all dimensions to ensure that the tub enclosure is properly sized for your whirlpool tub.
  • Detailed installation instructions are available on the installation page of this site.
  • Re-test your whirlpool tub for leaks or construction damage before you enclose your tub.

 

Receiving

Reliable trucking (freight) companies have been selected by WaterTech Whirlpools to deliver each new Whirlpool Bath. WaterTech Whirlpools packages each bath individually to ensure safe delivery to each customer. The freight carrier will notify customer and schedule a delivery time after the bath leaves our manufacturing facility. Call WaterTech Whirlpools if you have any questions (i.e. price, product, technical, shipping etc.) Phone 1-800-289-8827, Fax: 423-926-6438 email at info@watertechtn.com.

INSPECTION AND CLAIMS PROCEDURE: Follow the steps below to eliminate any questions about who is responsible for visible or concealed damage that may have occurred in shipping. Examine the shipping box for signs of damage or mishandling, i.e. staples pulled loose, flaps unglued, punches to the box, severe indentations, or crushed corners. If the box is damaged, the delivery person and receiving person / Consignee must note the damage to the box on delivery paperwork before opening the box. Open the box and inspect the tub for damage. If damage is found, call WaterTech Whirlpools at 1-800-289-8827 before accepting tub. Minor defects such as scuffs, scratches, etc… can be easily taken care of by one of our service people. All issues need to be resolved before signing delivery paperwork.

CONCEALED DAMAGE: WaterTech Whirlpools allows the consignee / owner no more than 48 hours from time of receipt to inspect and report any concealed damage (i.e. leaks, broken pipes, etc…) or shortages of merchandise ordered (i.e. heater, drain, jet trim, etc…). Report concealed damage and shortage to Americas Best Whirlpools 1-800-289-8827.

FAILURE OF THE CONSIGNEE TO INSPECT AND REPORT ANY CONCEALED DAMAGE WITHIN THE 48 HOUR PERIOD PLACES FULL RESPONSIBILITY FOR ANY CONCEALED DAMAGE ON THE CONSIGNEE.

PRE-TEST YOUR TUB: You must pretest your tub for leaks within 48 hours of receipt. WaterTech Whirlpools tubs go through rigorous testing for plumbing leaks and proper operation prior to shipping, but as a secondary precaution, the tub must be re-tested for leaks and proper operation within the allotted 48 hours and before installation. Test your tub in a location that will not be damaged by spilled water such as a basement, driveway, or a garage. Pre-testing your tub allows you to find any plumbing connections that might have worked loose during shipping.

HOW TO PRE-TEST YOUR TUB: Place your tub on a firm flat surface, make sure top of tub is level in all directions. Tape over the drain. Fill with water to 1 or 2 inches above the highest jet. Plug the motor into a GFCI protected outlet, and with the pump running, check all pipes and fittings for moisture. If no leaks are found, remove tape over drain and check for proper drainage. If all is correct, you may continue the Installation process.

IF ANY PROBLEMS ARE DISCOVERED DO NOT INSTALL THE TUB UNTIL YOU HAVE SPOKEN WITH A WATERTECH WHIRLPOOLS REPRESENTATIVE AT 1-800-289-8827

Related Products

Expedited Production

Available to those who want to guarantee that their order will ship within 5 days after order is placed. Holidays and Weekends excluded. was last modified: December 13th, 2017
$148.00

Turbo Charging System

The turbo charging system is composed of a single speed, 1 h.p., 675 watt heated airblower, hoses, controls, 8 port manifold and is factory installed. Turbo charging a whirlpool bath system allows jets to provide...
$325.00

Pulsating Jet

Jet nozzle spins and produces a pulsing action. This type of jet is often requested in the foot and back areas. Jet pulsation is adjustable. was last modified: December 13th, 2017
$55.00

Deep Soak Overflow Drain

Price:

Chrome: $82
Nickel: $99
Polished Brass: $110
Oil-Rubbed Bronze: $110
 
$82.00

Acrylic Skirt

Removable acrylic skirts available in 5' & 6' lengths. White, Bone, Designer, Marble, & Granite Colors available.
$267.00

Jet Finishes

Chrome: $274
Nickel: $343
Polished Brass: $321
Oil-Rubbed Bronze: $370
Watertech offers a beautiful variety of jet finishes for your tub, available in chrome, nickel, polished brass and oil-rubbed bronze. Note: White and bone jets are standard in all tubs with some other colors available. For Walk-in bath tubs the standard finish is chrome.
$274.00

Underwater Mood Light

A clear light with interchangeable blue, red and clear lenses. was last modified: December 13th, 2017
$123.00

Cascading Fill and Drain Faucet

Chrome: $525
Brass: $675
Nickel: $651
Oil-Rubbed Bronze: $675
All our designer faucetry come from the American Faucet and Coatings Corporation, which specialize in high end manufacturing for the bath and kitchen industry. This family owned business is located in Vista, CA and employs over 100 skilled workers that operate out of a 100,000 sq ft factory. All our faucets use German made ¼ turn ceramic disc cartridges with a lifetime warranty. Spouts, handles, escutcheons and valves are solid brass! Not plastic or stamped metal.
$525.00

Roman 4-Piece Faucet Set

Chrome: $530
Nickel: $605
Bronze: $665
All our designer faucetry come from the American Faucet and Coatings Corporation, which specialize in high end manufacturing for the bath and kitchen industry. This family owned business is located in Vista, CA and employs over 100 skilled workers that operate out of a 100,000 sq ft factory. All our faucets use German made ¼ turn ceramic disc cartridges with a lifetime warranty. Spouts, handles, escutcheons and valves are solid brass! Not plastic or stamped metal.
$530.00

Injector Finishes

Chrome: $274
Nickel: $343
Polished Brass: $321
Oil-Rubbed Bronze: $370
Watertech offers a beautiful variety of injector finishes for your tub, available in chrome, nickel, polished brass and oil-rubbed bronze. Note: White and bone jets are standard in all tubs with some other colors available. For Walk-in bath tubs the standard finish is chrome.
$274.00
Back to top
Follow by Email
Facebook
Facebook
Contact us

We would love to help you answer all your questions. Please fill out the form below and we will get back to you ASAP or call us at: 1 (800) 289-8827.

Questions, issues or concerns? I'd love to help you!

Click ENTER to chat